TM AccusprayTM HG & HGP System
3M Paint Spray Equipment


The new 3MTM ACCUSPRAYTM-SYSTEM is the latest addition to the 3M PPSTM system, utilizing a composite HVLP gravity feed spray gun with replacement spray heads. We can no longer say "there is not a spray gun that requires cleaning".

The 3MTM HG Accuspray gun provides the most important feature EXCELLENT ATOMIZATION with the convenience of 5 to 8 spray outs before the head needs replacement. When the needle packing seal starts to leak back into the clear fluid tube the head needs replacement. The average head cost per spray-out is $0.50 to $0.60.

FEATURE
HVLP Spray Technology
Excellent Atomization
New Head Replacement
BENEFIT
Lowers coating usage and saves money
Smoother Finish
"Like New Gun Performance"


APPLICATIONS


The HG Accuspray gun with the 1.8mm fluid nozzle was targeted for the priming and sealing in the automotive refinish business. We find that the 1.8mm orifice size matches rhe required flow rate of industrial coatings. The 1.3mm and 1.4mm fluid nozzle are for medium viscosity coatings including automotive basecoat and clearcoats. The 1.2mm flulid nozzle is for applying stains. This gun requires 13 CFM at 20 psi.

Click here for a video demonstration.



3MTM HG and HGP Care and Cleaning Procedures

Do not backpressure the gun.

There are two teflon O-rings or seals in the atomizing head. When you slide the atomizing head onto the needle the seals are pushed out towards the front of the gun. This seals the needle passage so the air and fluid going through the gun does not blow back into the gun body. If you back pressure the gun it will flip the teflon seals so they point back into the gun. When you add fluid and pressure it sneaks past the seals and comes out in front of the handle.

The solution is to clean the gun properly.

While the atomizing head is on the gun, fill it half way with whatever cleaner is required for your coating. Cover and shake it a bit to loosen any residue. Pull the trigger and drain. Fill the atomizing head two more times with cleaner and drain through the tip by pulling the trigger. Pull the atomizing head straight off the gun. Do not twist as you're pulling. Fill the needle port on the back side of the atomizing head with cleaner and drain. Inspect to make sure there is no residue left in the atomizing head and repeat if needed.

3MTM AccusprayTM HG "All In One" Spray Gun Package containing HG gun, air regulator, 1.4mm, 1.8mm, & 2.0mm atomizing heads, 22 ounce PPS cup with 5 liners and lids, with mix ratio card. $10.00 3M rebate when mailed by 12-31-15. See backside of blister pack for details. P/N 16580. Replaces 16570 HG18 gun.
Our Price

$200.00
Quantity




3MTM AccusprayTM-System Gun Atomizing Head Refill Kit 1.2MM, Four (4)blue heads per carton. For use on all HGXX and HGP guns. P/N 16615.
Our Price

$16.35
Quantity




3MTM AccusprayTM-System Gun Atomizing Head Refill Kit 1.3MM, Four (4)green heads per carton. For use on all HGXX and HGP guns. P/N 16614.
Our Price

$16.35
Quantity




3MTM AccusprayTM-System Gun Atomizing Head Refill Kit 1.4MM, Four (4)orange heads per carton. For use on all HGXX and HGP guns. P/N 16612.
Our Price

$20.45
Quantity




3MTM AccusprayTM-System Gun Atomizing Head Refill Kit 1.8MM, Four (4) clear heads per carton. For use on all HGXX and HGP guns. P/N 16611.
Our Price

$20.45
Quantity




3MTM AccusprayTM-System Gun Atomizing Head Refill Kit 2.0MM, Four (4) red heads per carton. For use on all HGXX and HGP guns. P/N 16609.
Our Price

$20.45
Quantity




3MTM ACCUSPRAYTM-SYSTEM FLOW CONTROL WITH GAUGE (CHEATER VALVE), With 1/4" NPS male inlet, and 1/4" NPS female swivel outlet. P/N 16573
Our Price

$26.10
Quantity




Click Here for PPS Cups, Liners, & Lids

3MTM AccusprayTM HGP Gravity Pressure Feed Composite Spray Gun - To spray very high solids such as: gel-coat, polyester, epoxies, adhesives, and boat bottom coatings, etc. Includes two 2.0mm and two 1.8mm replacement heads. PPS H/0 pressure cup with liners and lids sold separately, see below. P/N 16587.
Our Price

$214.25
Quantity




3MTM AccusprayTM Large PPS Pressure Cup Starter Kit - Contains 28 oz. H/0 pressure cup with 12 liners and lids (200 micron), P/N AFS-1441
Our Price

$108.55
Quantity




3MTM AccusprayTM Small PPS Pressure Cup Starter Kit - Contains 6 oz. H/0 pressure cup with 10 liners and lids (200 micron), P/N AFS-1442
Our Price

$61.65
Quantity




    
    


LOCATE:


Finish Systems
2691 S. Calhoun Road, New Berlin, WI 53151
Hours: Monday - Friday 8:00 - 4:30

Order Toll Free 800-657-0703
Phone 262-784-5977 Fax 262-784-5975
www.finishsystems.com
E-mail sales@finishsystems.com


Spray Guns | Pressure Pots | Painting Supplies | AAA | WAGNER Powder & Wet Spray Equipment | Spray Booths | Setups
GO Compressor Gun/Cup Setups | Diaphragm Pumps | Aluminum Air Pipe | Air Purification
Force Curing Products | Clearance | Site Map | Top 12 Painter's Needs | Company Information
Policies | Contact Us | Q & A | Credit Application | Customer Comments | Careers | Home


Content Copyright © 1997-2014 by  Finish Systems.