RapidAir FastPipe Spanner Wrench (Various Sizes)
RapidAir FastPipe Spanner Wrench (Various Sizes)
$6.00
The RapidAir FastPipe spanner wrench is for use with the FastPipe compressed air system. Two spanner wrenches are required to tighten the FastPipe fittings when installing the FastPipe blue rigid aluminum air pipe system. Please note that you will need to purchase the correct sized spanner wrench for the size FastPipe you are installing and two wrenches are required for proper FastPipe installation (spanner wrenches are sold individually).
Description
Specifications:
- RapidAir FastPipe spanner wrench sizes (wrench size based on size of FastPipe you are installing): ¾”, 1”, 1 ½”, 2” & 3”
- Spanner wrenches are sold individually (2 are required for installation)
FastPipe Installation Steps:
- CUT PIPE TO LENGTH with tubbing cutter (cut must be square)
(DO NOT USE HACK SAW)
- DEBURR the end of the pipe outside and inside
(a smooth edge allows easy fitting assembly and no damage to the fitting o-ring)
- MARK END OF PIPE for the proper insertion depth
- ¾” Fittings: 2 inches
- 1” Fittings: 2 ¾ inches
- 1 ½” Fittings: 4 inches
- 2” Fittings: 4 ¾ inches
- 3” Fittings: 4 ½ inches
- WET END OF PIPE, with very diluted soapy water
(DO NOT USE ANY OIL OR GREASE LUBRICANT)
- LOOSEN fitting cone nut partially
LOOK INSIDE EACH FITTING FOR INNER PARTS
(inner parts, o-ring, stainless steel bite ring)
- INSERT PIPE into fitting until pipe bottoms out
HAND TIGHTEN fitting
FULLY TIGHTEN fitting with FastPipe spanner wrenches
*(Please note that two spanner wrenches are required for proper FastPipe installation. The spanner wrench can also be purchased as part of the installation tool kit based on the size of FastPipe that you are installing. In addition, the Pipe Selection Guide and Quote Form can be found below).
Related Products
Product Inquiry
Have a question about this product?
Fill the form below and we will respond to you as soon as possible.
Specifications:
- RapidAir FastPipe spanner wrench sizes (wrench size based on size of FastPipe you are installing): ¾”, 1”, 1 ½”, 2” & 3”
- Spanner wrenches are sold individually (2 are required for installation)
FastPipe Installation Steps:
- CUT PIPE TO LENGTH with tubbing cutter (cut must be square)
(DO NOT USE HACK SAW)
- DEBURR the end of the pipe outside and inside
(a smooth edge allows easy fitting assembly and no damage to the fitting o-ring)
- MARK END OF PIPE for the proper insertion depth
- ¾” Fittings: 2 inches
- 1” Fittings: 2 ¾ inches
- 1 ½” Fittings: 4 inches
- 2” Fittings: 4 ¾ inches
- 3” Fittings: 4 ½ inches
- WET END OF PIPE, with very diluted soapy water
(DO NOT USE ANY OIL OR GREASE LUBRICANT)
- LOOSEN fitting cone nut partially
LOOK INSIDE EACH FITTING FOR INNER PARTS
(inner parts, o-ring, stainless steel bite ring)
- INSERT PIPE into fitting until pipe bottoms out
HAND TIGHTEN fitting
FULLY TIGHTEN fitting with FastPipe spanner wrenches
*(Please note that two spanner wrenches are required for proper FastPipe installation. The spanner wrench can also be purchased as part of the installation tool kit based on the size of FastPipe that you are installing. In addition, the Pipe Selection Guide and Quote Form can be found below).
Have a question about this product?
Fill the form below and we will respond to you as soon as possible.