3M™ Accuspray™ ONE Spray Gun System with PPS™ Series 2.0 Spray Cup System – (26580)
3M™ Accuspray™ ONE Spray Gun System with PPS™ Series 2.0 Spray Cup System – (26580)
$367.75
The 3M™ Accuspray™ ONE Spray Gun System with Standard PPS™ Series 2.0 combines the simplicity and easy maintenance of our Accuspray™ spray gun with the material-saving, rapid clean-up convenience of PPS™ Series 2.0, the next generation, highest performing disposable spray cup system. Replaceable atomizing heads afford the performance of a new gun, on demand and at a fraction of the cost.
ONE System for Every Spraying Need
The 3M™ Accuspray™ ONE Spray Gun System with PPS™ Series 2.0 is the combination of convenience, versatility and efficiency. This system features the Accuspray™ ONE Spray Gun - a lightweight, composite spray gun body designed to eliminate the complexity of a traditional spray gun. This gun body has been engineered for enhanced durability in automotive and industrial environments. The spray gun uses a series of replaceable, see-through atomizing heads which can be reused 5-10 times and then simply removed and replaced. This affords the performance of a brand new spray gun, on demand and at a fraction of the price.
Replaceable Atomizing Heads for the 3M™ Accuspray™ ONE Spray Gun System with PPS™ Series 2.0
Our 3M™ Accuspray™ Atomizing Heads for PPS™ Series 2.0 deliver the ideal atomization to a wide range of fluids and coatings applied with Accuspray™ ONE Spray Guns. Atomizing heads are available in five sizes: 2.0 mm (red), 1.8 mm (clear), 1.4 mm (orange), 1.3 mm (green) and 1.2 mm (blue). For sealers, basecoats and topcoats, we recommend 1.3 mm or 1.4 mm atomizing heads. Choose the 1.8 mm size for higher-viscosity materials such as primer, and the 2.0 mm size for heavy-duty applications using fluids like gel coats, adhesives, undercoats or industrial coatings. Always refer to your paint company’s recommendations. Fast, easy controls for fan diameter, fluid and air pressure on the Accuspray™ ONE gun allow for quick adjustment across jobs from spot repairs to full panel coverage requiring up to 12” vertical or horizontal spray patterns.
Along with the distinctive color, the fluid tip size is presented clearly on each atomizing head for fast, accurate selection. Atomizing heads are see-through to make it easy for technicians to determine that the head is properly cleaned.
All atomizing heads work with our PPS™ Series 2.0 Spray Cup System – a system of reusable paint cups and disposable lids and liners, so you can be done with cleaning paint cups forever. ONE gun – ONE system for a complete range of applications.
Description
Specifications:
- The 3m™ Accuspray™ ONE Spray gun is for use with compressed air systems only
- Air Inlet - 1/4” NPS (m)
- Maximum air inlet pressure is 24 psi (Maximum inlet pressure will yield approximately 10 psi (0.69 bar) at the air cap)
- Required atomizing air volume is 13 cfm
- Weight – 11.2 oz
- 5 to 8 spray outs before the head needs replacement
- For best atomization results use 13 cfm @ 20 psi
- Part Number 26580, 3M Stock # 7100163226 (Previous 3M Stock # 60455090773), UPC 00051131265806
3M™ Accuspray™ Gravity Spray Gun Kit Includes:
- (1) - 3M™ Accuspray™ Spray Gun Body
- (1) - Air Flow Control Valve & Gauge
- (1) - 125 micron lid
- (4) - 200 micron lids
- (1) - 650 ml (22 oz) standard size PPS™ 2.0 gravity hard cup
- (5) - 650 ml (22 oz) standard size PPS™ 2.0 liners
- (3) - PPS Plugs
- (1) - 1.2 mm (blue) PPS™ 2.0 gravity atomizing head
- (1) - 1.3 mm (green) PPS™ 2.0 gravity atomizing head
- (1) - 1.4 mm (orange) PPS™ 2.0 gravity atomizing head
- (1) - 1.8 mm (clear) PPS™ 2.0 gravity atomizing head
- (1) - 2.0 mm (red) PPS™ 2.0 gravity atomizing head
- (10) - Color Identification Clips (2 each of 5 colors)
- (1) - Quick start guide & owner’s manual
Additional atomizing heads and PPS liners and lids sold separately.
Information:
3M™ Accuspray™ ONE Spray Gun System with PPS™ Series 2.0 Spray Cup System 26580 - Owner's Manual
Please note that the spray gun does not require a repair kit. For more detailed information on the spray gun such as parts, setup & maintenance, please review the Owner’s Manual.
Note:
3MTM HG and HGP Care and Cleaning Procedures
Do not backpressure the gun.
There are two Teflon O-rings or seals in the atomizing head. When you slide the atomizing head onto the needle the seals are pushed out towards the front of the gun. This seals the needle passage so the air and fluid going through the gun does not blow back into the gun body. If you back pressure the gun it will flip the Teflon seals so they point back into the gun. When you add fluid and pressure it sneaks past the seals and comes out in front of the handle.
The solution is to clean the gun properly.
While the atomizing head is on the gun, fill it half way with whatever cleaner is required for your coating. Cover and shake it a bit to loosen any residue. Pull the trigger and drain. Fill the atomizing head two more times with cleaner and drain through the tip by pulling the trigger. Pull the atomizing head straight off the gun. Do not twist as you're pulling. Fill the needle port on the back side of the atomizing head with cleaner and drain. Inspect to make sure there is no residue left in the atomizing head and repeat if needed.
Related Products
Product Inquiry
Have a question about this product?
Fill the form below and we will respond to you as soon as possible.
Specifications:
- The 3m™ Accuspray™ ONE Spray gun is for use with compressed air systems only
- Air Inlet - 1/4” NPS (m)
- Maximum air inlet pressure is 24 psi (Maximum inlet pressure will yield approximately 10 psi (0.69 bar) at the air cap)
- Required atomizing air volume is 13 cfm
- Weight – 11.2 oz
- 5 to 8 spray outs before the head needs replacement
- For best atomization results use 13 cfm @ 20 psi
- Part Number 26580, 3M Stock # 7100163226 (Previous 3M Stock # 60455090773), UPC 00051131265806
3M™ Accuspray™ Gravity Spray Gun Kit Includes:
- (1) - 3M™ Accuspray™ Spray Gun Body
- (1) - Air Flow Control Valve & Gauge
- (1) - 125 micron lid
- (4) - 200 micron lids
- (1) - 650 ml (22 oz) standard size PPS™ 2.0 gravity hard cup
- (5) - 650 ml (22 oz) standard size PPS™ 2.0 liners
- (3) - PPS Plugs
- (1) - 1.2 mm (blue) PPS™ 2.0 gravity atomizing head
- (1) - 1.3 mm (green) PPS™ 2.0 gravity atomizing head
- (1) - 1.4 mm (orange) PPS™ 2.0 gravity atomizing head
- (1) - 1.8 mm (clear) PPS™ 2.0 gravity atomizing head
- (1) - 2.0 mm (red) PPS™ 2.0 gravity atomizing head
- (10) - Color Identification Clips (2 each of 5 colors)
- (1) - Quick start guide & owner’s manual
Additional atomizing heads and PPS liners and lids sold separately.
Information:
3M™ Accuspray™ ONE Spray Gun System with PPS™ Series 2.0 Spray Cup System 26580 - Owner's Manual
Please note that the spray gun does not require a repair kit. For more detailed information on the spray gun such as parts, setup & maintenance, please review the Owner’s Manual.
Note:
3MTM HG and HGP Care and Cleaning Procedures
Do not backpressure the gun.
There are two Teflon O-rings or seals in the atomizing head. When you slide the atomizing head onto the needle the seals are pushed out towards the front of the gun. This seals the needle passage so the air and fluid going through the gun does not blow back into the gun body. If you back pressure the gun it will flip the Teflon seals so they point back into the gun. When you add fluid and pressure it sneaks past the seals and comes out in front of the handle.
The solution is to clean the gun properly.
While the atomizing head is on the gun, fill it half way with whatever cleaner is required for your coating. Cover and shake it a bit to loosen any residue. Pull the trigger and drain. Fill the atomizing head two more times with cleaner and drain through the tip by pulling the trigger. Pull the atomizing head straight off the gun. Do not twist as you're pulling. Fill the needle port on the back side of the atomizing head with cleaner and drain. Inspect to make sure there is no residue left in the atomizing head and repeat if needed.
Have a question about this product?
Fill the form below and we will respond to you as soon as possible.
