RapidAir FastPipe Deburring Tool (Various Sizes)
RapidAir FastPipe Deburring Tool (Various Sizes)
$30.85
The RapidAir FastPipe deburring tool is for use with the FastPipe compressed air system. The deburring tool is needed to create a smooth edge on the inside and outside of the end of the pipe. The smooth edge allows the fitting assembly to go on easier and eliminates any potential damage to the fitting O-ring which may cause a leak. Please note that you will need to purchase the correct sized deburr tool for the size FastPipe you are installing.
Description
Specifications:
- RapidAir FastPipe deburr tool sizes (tool size based on size of FastPipe you are installing): ¾” – 1”, ¾” – 2” & 3”
- An electric drill is required for the 3” deburring tool (not included)
- Deburring tools are sold individually
FastPipe Installation Steps:
- CUT PIPE TO LENGTH with tubbing cutter (cut must be square)
(DO NOT USE HACK SAW)
- DEBURR the end of the pipe outside and inside
(a smooth edge allows easy fitting assembly and no damage to the fitting o-ring)
- MARK END OF PIPE for the proper insertion depth
- ¾” Fittings: 2 inches
- 1” Fittings: 2 ¾ inches
- 1 ½” Fittings: 4 inches
- 2” Fittings: 4 ¾ inches
- 3” Fittings: 4 ½ inches
- WET END OF PIPE, with very diluted soapy water
(DO NOT USE ANY OIL OR GREASE LUBRICANT)
- LOOSEN fitting cone nut partially
LOOK INSIDE EACH FITTING FOR INNER PARTS
(inner parts, o-ring, stainless steel bite ring)
- INSERT PIPE into fitting until pipe bottoms out
HAND TIGHTEN fitting
FULLY TIGHTEN fitting with FastPipe spanner wrenches
*(Please note that the deburring tool size (range) needs to match the FastPipe that you are working with to ensure that they will work properly. The deburring tool can also be purchased as part of the installation tool kit based on the size of FastPipe that you are installing. In addition, the Pipe Selection Guide and Quote Form can be found below).
Related Products
Product Inquiry
Have a question about this product?
Fill the form below and we will respond to you as soon as possible.
Specifications:
- RapidAir FastPipe deburr tool sizes (tool size based on size of FastPipe you are installing): ¾” – 1”, ¾” – 2” & 3”
- An electric drill is required for the 3” deburring tool (not included)
- Deburring tools are sold individually
FastPipe Installation Steps:
- CUT PIPE TO LENGTH with tubbing cutter (cut must be square)
(DO NOT USE HACK SAW)
- DEBURR the end of the pipe outside and inside
(a smooth edge allows easy fitting assembly and no damage to the fitting o-ring)
- MARK END OF PIPE for the proper insertion depth
- ¾” Fittings: 2 inches
- 1” Fittings: 2 ¾ inches
- 1 ½” Fittings: 4 inches
- 2” Fittings: 4 ¾ inches
- 3” Fittings: 4 ½ inches
- WET END OF PIPE, with very diluted soapy water
(DO NOT USE ANY OIL OR GREASE LUBRICANT)
- LOOSEN fitting cone nut partially
LOOK INSIDE EACH FITTING FOR INNER PARTS
(inner parts, o-ring, stainless steel bite ring)
- INSERT PIPE into fitting until pipe bottoms out
HAND TIGHTEN fitting
FULLY TIGHTEN fitting with FastPipe spanner wrenches
*(Please note that the deburring tool size (range) needs to match the FastPipe that you are working with to ensure that they will work properly. The deburring tool can also be purchased as part of the installation tool kit based on the size of FastPipe that you are installing. In addition, the Pipe Selection Guide and Quote Form can be found below).
Have a question about this product?
Fill the form below and we will respond to you as soon as possible.
